Pièces détachées TI-Nspire CX faciles sur eBay et Taobao !

[critor]

Ta TI-Nspire CX est en panne ?
Contrairement à d'autres constructeurs, Texas Instruments ne nous semble pas avoir un bon service de fourniture de pièces détachées pour le grand public.
Le site https://epsstore.ti.com dispose en effet d'un catalogue assez réduit, ne fournissant que des pièces remplaçables sans ouvrir la calculatrice et donc sans aucun intérêt pour une réparation :

• couvercles
• batteries
• câbles
• patins anti-dérapant

De plus, tous les modèles ne bénéficient pas de l'ensemble de ces pièces.
Et encore, ça c'est si tu choisis de dire que tu es en Amérique du Nord. Car si tu dis que tu es en Europe, le choix est encore plus ridicule...

Que faire donc si ta TI-Nspire CX n'est pas sous garantie, si tu n'as pas envie de renvoyer ta calculatrice pour attendre le retour de la machine réparée ou échangée, ou si ta panne n'est pas couverte par la garantie comme par exemple un bris de l'écran ?

Dans un article précédent, nous te parlions de la possibilité d'acheter ton écran pour ta TI-Nspire CX en révision matérielle A-V sur https://world.taobao.com/item/19576473009.htm .
Mais voilà, Taobao est un site chinois. Il te faudra non seulement comprendre le chinois, mais également fournir les précisions sur ta demande en chinois... Quant au paiement, les chinois ne connaissent pas Paypal...

Et bien bonne nouvelle désormais, puisqu'une boutique chinoise fait désormais l'effort de s'afficher en anglais sur eBay international, avec un stock de plus de 10 écrans TI-Nspire CX !

Dans un autre article, toujours sur Taobao, nous t'informions de la disponibilité des cartes mère pour TI-Nspire CX et pour TI-Nspire CX CAS, pour révision matérielle A-V.
Mêmes problèmes de communication et de paiement pour acheter.

Mais désormais, tu disposes de plusieurs sites internationaux se proposant pour une petite commission de réaliser pour toi toutes les démarches après des vendeurs chinois de Taobao, comme par exemple https://taobaofocus.com/ .

Attention toutefois à bien commander la carte mère correspondant à ton modèle, TI-Nspire CX ou TI-Nspire CX CAS.
Car le clavier de ta calculatrice dispose lui aussi d'une protection : il enregistre le type de ta calculatrice.

Si tu mets une carte mère TI-Nspire CX CAS dans un boîtier TI-Nspire CX ou une carte mère TI-Nspire CX dans un boîtier TI-Nspire CX CAS, le système refusera de démarrer en te prétendant qu'il ne reconnaît pas le clavier et que tu dois le remplacer.

Mais si tu y tiens, d'autres pièces détachées TI-Nspire CX, pour révision matérielle A-N ou A-V selon la pièce, sont également disponibles sur https://world.taobao.com/item/547499180 ... .11.FPN1ts , dont justement la carte clavier TI-Nspire CX CAS...

[Cloé Christmann]

Quelqu'un aurai un lien pour la pièce plastique transparent qui protège l'écran ?

[critor]

https://world.taobao.com/item/547499180 ... .11.FPN1ts
En demandant la pièce C :

[BrainPortable]

This reminds me something.

Some interesting thing is that in China there are always some sellers on Taobao providing "used" TI-Nspire CXs at a very low price. For example, I bought my "used" CX CAS for about 54.27€, which a brand new one costs about 162.81€ in China. And these guys sometimes sell broken CXs, which could still be disassembled for using as components, only costs about 27.14€, and if you are good at restoration, they can still be used normally after some repairing.

A thing need to be noticed is that you can always find a hole drilled on the CXs they sell, sometimes on the circult board, sometimes even on the screen or on the keypad(this kind of CX is impossible to be used normally).This shows that the CXs they sell are mainly from the electronic garbage recycling factory. What they are selling are not "used" calculators-- they are actually selling electronic garbage.That hole is drilled by the recycling factories to prevent someone put them onto market again.

I once asked for someone who did this kind of job, and he told me that the hole is drilled by the recycling factories, sometimes only on the circult board, sometimes the whole calculator is being drilled through. Then the seller get these garbage calculators and check out where the hole is. If it is not on the critical components, such as LCD or chips inside, the will try to repair it and then sell them as "used" ones. Otherwise, they will sell them as "broken" ones.

[parrotgeek1]

This reminds me something.

Some interesting thing is that in China there are always some sellers on Taobao providing "used" TI-Nspire CXs at a very low price. For example, I bought my "used" CX CAS for about 54.27€, which a brand new one costs about 162.81€ in China. And these guys sometimes sell broken CXs, which could still be disassembled for using as components, only costs about 27.14€, and if you are good at restoration, they can still be used normally after some repairing.

A thing need to be noticed is that you can always find a hole drilled on the CXs they sell, sometimes on the circult board, sometimes even on the screen or on the keypad(this kind of CX is impossible to be used normally).This shows that the CXs they sell are mainly from the electronic garbage recycling factory. What they are selling are not "used" calculators-- they are actually selling electronic garbage.That hole is drilled by the recycling factories to prevent someone put them onto market again.

I once asked for someone who did this kind of job, and he told me that the hole is drilled by the recycling factories, sometimes only on the circult board, sometimes the whole calculator is being drilled through. Then the seller get these garbage calculators and check out where the hole is. If it is not on the critical components, such as LCD or chips inside, the will try to repair it and then sell them as "used" ones. Otherwise, they will sell them as "broken" ones.

I really wish some people would sell the used calculators on Aliexpress! Even for 70 EUR It could make it so much easier for people to get CX calculators.

Out of curiosity, How much does a new CM-C cost in Euros?

[BrainPortable]

This reminds me something.

Some interesting thing is that in China there are always some sellers on Taobao providing "used" TI-Nspire CXs at a very low price. For example, I bought my "used" CX CAS for about 54.27€, which a brand new one costs about 162.81€ in China. And these guys sometimes sell broken CXs, which could still be disassembled for using as components, only costs about 27.14€, and if you are good at restoration, they can still be used normally after some repairing.

A thing need to be noticed is that you can always find a hole drilled on the CXs they sell, sometimes on the circult board, sometimes even on the screen or on the keypad(this kind of CX is impossible to be used normally).This shows that the CXs they sell are mainly from the electronic garbage recycling factory. What they are selling are not "used" calculators-- they are actually selling electronic garbage.That hole is drilled by the recycling factories to prevent someone put them onto market again.

I once asked for someone who did this kind of job, and he told me that the hole is drilled by the recycling factories, sometimes only on the circult board, sometimes the whole calculator is being drilled through. Then the seller get these garbage calculators and check out where the hole is. If it is not on the critical components, such as LCD or chips inside, the will try to repair it and then sell them as "used" ones. Otherwise, they will sell them as "broken" ones.

I really wish some people would sell the used calculators on Aliexpress! Even for 70 EUR It could make it so much easier for people to get CX calculators.

Out of curiosity, How much does a new CM-C cost in Euros?

A brand new CM-C costs about 71.64€, and a CM-C CAS costs about 77.06€.

However, I remember that CMs are sold almost twice the price about a year or two ago. Maybe it's TI decided to stop the support for CM series that caused resellers to reduce the price to sell more products.

[critor]

Some interesting thing is that in China there are always some sellers on Taobao providing "used" TI-Nspire CXs at a very low price. For example, I bought my "used" CX CAS for about 54.27€, which a brand new one costs about 162.81€ in China. And these guys sometimes sell broken CXs, which could still be disassembled for using as components, only costs about 27.14€, and if you are good at restoration, they can still be used normally after some repairing.

Interesting.

Do you have some current taobao links which could illustrate this ?

Thanks.

[BrainPortable]

Some interesting thing is that in China there are always some sellers on Taobao providing "used" TI-Nspire CXs at a very low price. For example, I bought my "used" CX CAS for about 54.27€, which a brand new one costs about 162.81€ in China. And these guys sometimes sell broken CXs, which could still be disassembled for using as components, only costs about 27.14€, and if you are good at restoration, they can still be used normally after some repairing.

Interesting.

Do you have some current taobao links which could illustrate this ?

Thanks.

Well, nowadays it seems to be not that easy to find cheap CX sellers...

However, there are still some guys selling.

https://item.taobao.com/item.htm?spm=a2 ... t=3#detail
Used CX (Bad looking ones but works) for 50.88€. Shipping not included. Only 1 left.
Used CX (Good looking ones) for 58.34€. Shipping not included. Only 1 left.
Used CX (Almost new) for 106.51€. Shipping not included. Only 1 left.
Warning: This guy is famous for his low price but also famous for his bad attitude to customers(especially when his things going wrong or you want a refund). Don't buy his things unless you really want it.

https://item.taobao.com/item.htm?spm=a2 ... t=3#detail
CX CAS that seems to be new for 78.69€. Shipping to China mainland included. 55 left.

BTW, used Clickpads are usually sold at 20.35€~40.70€ in China.

[critor]

Some interesting thing is that in China there are always some sellers on Taobao providing "used" TI-Nspire CXs at a very low price. For example, I bought my "used" CX CAS for about 54.27€, which a brand new one costs about 162.81€ in China. And these guys sometimes sell broken CXs, which could still be disassembled for using as components, only costs about 27.14€, and if you are good at restoration, they can still be used normally after some repairing.

Interesting.

Do you have some current taobao links which could illustrate this ?

Thanks.

Well, nowadays it seems to be not that easy to find cheap CX sellers...

Indeed, I can't find any Nspire prototype...
https://world.taobao.com/search/search. ... e&q=nspire

And I also noted that there hasn't been topics about protototypes for months now on cncalc.org, although they were quite frequent 2 years ago.
Is it related ? Do you know what happened ?...